Exploring Sawdust as a Sustainable Alternative in Block Production: A Study on Compressive Strength and Environmental Impact

Authors

  • Samuel Kotey Department of Construction Management and Technology, School of Built and Natural Environment, Cape Coast, Ghana
  • Zakari Mustapha Department of Construction Management and Technology, School of Built and Natural Environment, Ghana
  • Benjamin Boahene Akomah Department of Construction Management and Technology, School of Built and Natural Environment, Ghana
  • Mensah Michael Department of Construction Management and Technology, School of Built and Natural Environment, Ghana
  • Adomako Sampson Department of Construction Management and Technology, School of Built and Natural Environment, Ghana
  • Antwi Solomon Department of Construction Management and Technology, School of Built and Natural Environment, Ghana

DOI:

https://doi.org/10.51983/tarce-2023.12.2.4130

Keywords:

Building Material, Compressive Strength, Eco-Friendly, Sustainable, Thermal Insulation Properties

Abstract

The utilisation of sawdust in block manufacture has effectively minimised the amount of waste material being disposed of in landfills. The study aimed to examine the utilisation of sawdust as a partial substitute for sand in the manufacture of blocks and assess the compressive strength of sandcrete and sawdust blocks. The experiment utilised cement grade 32.5R, pit sand as the fine aggregate, fine particles of sawdust, and a water-cement ratio of 0.65. Control specimen 0,utilised 10%, 15%, and 20% of fine sawdust particles as partial substitutes for sand. Subsequently, the materials were combined in a proportion of 1:3 to generate sawdust and sandcrete blocks. The block samples were cured by applying water at intervals of 7, 14, and 21 days, respectively. The results indicate a significant alteration in the water-cement ratio employed during the material batching and mixing procedure of the sawdust samples. Additional results revealed differences in the compressive strength and density tests between sandcrete and sawdust blocks in the control specimens. The compressive strength of sandcrete blocks was superior to that of sawdust blocks. Sandcrete blocks are suitable for load-bearing purposes in construction projects, whilst sawdust blocks are suitable for non-load-bearing walls.

References

O. O. Ogunniyi, O. S. Babatunde, and J. O. Akinmusuru, “Sawdust-cement composite blocks for building construction: A review,” Journal of Building Engineering, vol. 15, pp. 238-246, 2018.

D. O. Ekhuemelo, E. T. Gbaeren, and E. T. Tembe, “Evaluation of lime-treated mixed sawdust as a fractional replacement for sand in the production of sandcrete hollow blocks,” International Journal of Science and Engineering Investigations, vol. 6, no. 65, pp. 21-27, 2017.

D. M. Tiough and V. M. Nande, “An evaluation of the strength properties of commercially produced sandcrete blocks in Makurdi metropolis,” International Journal of Education Development, vol. 24, no. 1, pp. 1-10, 2019.

A. Mwango and C. Kambole, “Engineering characteristics and potential increased utilization of sawdust composites in construction-A review,” Journal of Building Construction and Planning Research, vol. 7, no. 3, pp. 59-88, 2019.

BS 6073-1, “Precast concrete masonry units - Part 1: Specification for precast concrete masonry units,” British Standards Institute BSI, London, UK, 1984.

BS EN 1364-4, “Fire resistance tests for non-loadbearing elements, Curtain walling - part configuration (incorporating corrigendum June 2014),” British Standards Institute BSI, London, UK, 2014.

BS EN 771-1, “Specification for masonry units. Clay masonry units (+A1:2015),” British Standards Institute BSI, London, UK, 2011.

BS 1881-124:2015+A1, “Testing Concrete - Methods for analysis of hardened concrete,” British Standards Institute BSI, London, UK, 2021.

D. O. Ekhuemelo, O. Ademu, and E. T. Tembe, “Physical and strength properties of bricks produced from Portland cement and sawdust of Danielia oliverii wood,” Pro Ligno, vol. 12, no. 4, 2016.

M. A. Abera, “Investigating the acceptable quantity of fine aggregate to be replaced with sawdust to obtain strong, lightweight, and economical results for HCB production,” International Journal of Advance Research, Ideas and Innovations in Technology, vol. 5, no. 5, pp. 391-395, 2019.

O. Popoola, S. Ayegbokiki, and M. Gambo, “Study of compressive strength characteristics of hollow sandcrete blocks partially replaced by sawdust ash,” International Organization of Scientific Research, vol. 5, no. 5, pp. 30-34, 2015.

Nigerian Building Code, First Edition, Lexis Nexis, Butterworth, 2016.

I. Awotunde, O. Ekundayo, J. Adetooto, T. Adelerin, and C. Alegbeleye, “Assessment of suitability of molten plastic and sawdust mixture for the production of lightweight composite building materials,” in CM50 Conference, pp. 187, 2021.

S. A. Mangi, N. B. Jamaluddin, Z. Siddiqui, S. A. Memon, and M. H. B. W. Ibrahim, “Utilization of sawdust in concrete masonry blocks: A review,” Mehran University Research Journal of Engineering & Technology, vol. 38, no. 2, pp. 487-494, 2019.

BS EN 197-1, “Cement, Composition, specifications and conformity criteria for common cement (Incorporating corrigenda November 2011, October 2015 and February 2019),” British Standards Institute BSI, London, UK, 2011.

Downloads

Published

05-12-2023

How to Cite

Kotey, S., Mustapha, Z., Boahene Akomah, B., Michael, M., Sampson, A., & Solomon, A. (2023). Exploring Sawdust as a Sustainable Alternative in Block Production: A Study on Compressive Strength and Environmental Impact. The Asian Review of Civil Engineering, 12(2), 16–23. https://doi.org/10.51983/tarce-2023.12.2.4130

Issue

Vol. 12 No. 2 (2023): July-December 2023

Section

Articles

License

Copyright (c) 2023 The Research Publication

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.